Soffit and Fascia Replacement — Whole House in Vented Aluminum
Peeling, sagging, squirrel-chewed soffit and rotted fascia all the way around the house, replaced with vented aluminum that lets the attic breathe and never needs paint.
Reply within one business day. Or call / text 763-250-3621.
Whole-house soffit and fascia replacement: rotted wood soffit and fascia boards come off or are repaired, new subfascia goes on where it is needed, and vented aluminum soffit panels with F-channel and aluminum fascia cover finish the eaves and gables. JMB Builders does it across the Twin Cities metro, with gutters taken down and put back up on the new fascia. Priced per project from your photos, with a reply within one business day.
- Priced per project, eaves and gables, whole house
- Vented aluminum soffit, fascia cover, gutters rehung
- Quote from photos, reply within one business day
When the soffit and fascia are going in more than a couple of spots, patching stops making sense. The old plywood soffit is delaminating, the fascia has rotted behind every gutter hanger, the paint will not hold, and the squirrels have found the weak panel by the corner. Replacing all of it in aluminum turns the eaves into a surface that needs nothing for decades and, done right, gives the attic the intake air it has been missing.
The order matters. Gutters come down first. Rotted fascia and subfascia are cut out and replaced with new lumber, because aluminum fascia cover is a skin, not a structural board, and it has to be fastened to solid wood. Old soffit comes off where it is rotted or blocking the vents, and the insulation is pushed back from the eave so air can move. Then F-channel goes on the wall side, vented aluminum soffit panels are cut and fitted between the F-channel and the fascia, and aluminum fascia cover goes over the fascia board with a drip edge under the shingles. Gable ends get the same treatment with a matching frieze. Gutters go back up last, on new hidden hangers.
This is the whole-house version. For one rotted section behind a gutter or a soffit panel a raccoon opened, see our section repair page. If the roof or the siding is being done, the soffit and fascia fit into that job in the same order.
Get a written quote for this job
Three photos and a sentence is enough: a reply within one business day, or ask for a free in-home estimate. Or text the photos to 763-250-3621.
What you supply
- Photos of each side of the house showing the eaves and gables, plus close-ups of the worst spots
- A photo from inside the attic at the eave if you can get one; it shows whether the old soffit is vented
- Your color choice for the aluminum, or the trim color to match
What JMB supplies
- Gutters removed and rehung on new hidden hangers, or new seamless gutters quoted with the job
- Rotted fascia and subfascia cut out and replaced with new lumber, and rafter tails repaired where they have gone
- Old soffit removed where it is rotted or unvented; attic insulation pulled back from the eave with baffles set
- F-channel at the wall, vented aluminum soffit panels cut to length, and aluminum fascia cover with drip edge
- Gable soffit, frieze and rake trim wrapped to match
- Pest screening at the corners and any opening where squirrels or bats have been getting in
- Bath and dryer vents that end in the soffit rerouted to a proper exterior vent
- Photos of the finished eaves in your job folder
How it is priced: per project
Quoted in writing from your photos, with a reply within one business day. What moves the number:
- Total feet of eave and gable, and how wide the soffit overhang is
- How much fascia, subfascia and rafter tail rot has to be cut out and replaced before the aluminum goes on
- Removing old soffit and adding baffles vs. going over a sound, vented soffit
- One story vs. two, and how much staging the gables need
- Gutters rehung vs. replaced with new seamless gutters on the same visit
- Wrapping the frieze, rake trim and window heads to match
- Rerouting fan vents that dump into the soffit
Photos of all four sides from the yard and a couple of close-ups of the worst fascia are enough to quote; a look in the attic tells us whether the old soffit is vented.
How long it takes
A single-story ranch: two to three days. A two-story or a house with several gables: three to five days. Rot repair and gutters are included in those numbers.
How your project works
- 1
Send photos, get a written quote
Send three photos of the space and a sentence about what you want. You get a clear, itemized reply within one business day. Prefer a look in person? A free in-home estimate is always an option.
- 2
Pick materials, or bring your own
We help you choose profiles and materials that fit the house and the budget, or match your existing millwork exactly — or you buy the door or trim yourself and we install it. Everything is confirmed before the crew is scheduled.
- 3
Clean, precise installation
The crew shows up on time, protects floors and furniture, and installs with tight joints and consistent reveals. Photos of the finished work go in your job folder.
- 4
Walkthrough and invoice
We walk the finished work with you. If anything is not right, we fix it before we call the job done. Then one invoice, paid by check or direct deposit — no card fees, no payment links.
Situations and options
Vented aluminum soffit and fascia cover
The standard whole-house job: rotted wood replaced, F-channel and vented aluminum panels at every eave and gable, fascia cover with a drip edge under the shingles, in your color. Never needs paint.
Wood soffit replaced with aluminum
Old plywood or beadboard soffit removed, the eave opened up, insulation baffled back, and vented aluminum panels installed so the attic finally gets intake air. The fix for a hot attic and ice dams on a house with closed soffits.
Fascia cover over new wood fascia
Where the soffit is sound but the fascia is rotted behind the gutters, the fascia and subfascia are replaced in lumber and wrapped with aluminum fascia cover, with the gutters rehung on hidden hangers.
Soffit and fascia with a reroof or siding
During a roof replacement the drip edge and fascia cover tie together at the roof edge; during a siding job the F-channel and frieze tie into the new siding. We schedule the soffit and fascia in the right order inside the bigger job.
Soffit and Fascia Replacement — Whole House in Vented Aluminum: questions, answered
Should I replace all my soffit and fascia at once or just the bad sections?
If the rot is in one or two spots, a section repair is the right job and we quote it that way. If it is peeling, soft or sagging on more than a couple of runs, the paint will not hold, or the old soffit is unvented plywood, replacing the whole house in aluminum costs less per foot, gets the venting right everywhere, and ends the yearly patching. Photos of each side tell us which one you need.
Can aluminum fascia be installed over rotted wood fascia?
No, and that is the usual shortcut we undo. Aluminum fascia cover is a thin skin that is nailed to the fascia board; on soft wood the nails pull and the gutters come down with the first ice. We cut out the rotted fascia and subfascia, replace them with new lumber, and then wrap. What you see afterward is the same aluminum, but it is on solid wood.
Does vented soffit help with ice dams?
It helps when it is part of a working system: intake at the soffit, a clear path past the insulation with baffles, and exhaust at the ridge or roof vents. Cold air moving under the roof deck keeps the snow from melting from below, which is what forms the dam. Vented soffit over blocked insulation does nothing, so we pull the insulation back and set baffles when the old soffit comes off. Attic air sealing and insulation depth are the other half.
Do you take the gutters down for soffit and fascia replacement?
Yes, they have to come down to replace the fascia behind them. Sound gutters are removed, set aside and rehung on new hidden hangers at the end of the job. If they are sagging, split or spiked, we quote new seamless gutters with the job, since the fascia is new and it is the right time.
How long does soffit and fascia replacement take on a whole house?
A single-story ranch takes two to three days including rot repair and gutters. A two-story house or one with several gables takes three to five days, mostly because of staging. Weather matters less than on a roof, so it is a good fall or spring job.
Can you replace soffit and fascia before I get new gutters?
Yes, and that is the right order: fascia first, gutters after, so the gutters are hung on solid, wrapped fascia and not the other way around. If a gutter company is coming, we finish the fascia cover and drip edge and leave the eaves ready for them. Or the seamless gutters are run and hung with a seamless gutter machine as the last step of the same job.
Can you wrap wood fascia in aluminum?
Yes, when the wood is sound. Coil stock is bent on site to the fascia profile, tucked up under the drip edge so water cannot get behind it, and fastened with color-matched trim nails. Rotted fascia is replaced first, because wrapping rot traps water and hides it until the gutter pulls off.
Recent JMB work, from our job log
59 installs recorded across 30 Twin Cities communities since Dec 2025. Window and door installs for homeowners and the builders we work with. Counts come straight from our job log; no customer names.
Related jobs we do
Fascia Board Repair & Soffit Section Replacement
The gutter is pulling away, the fascia behind it is black and soft, and a soffit panel is hanging down. We replace the bad section, fix what caused it, and put the gutter back where it belongs.
Read moreGutter Installation — Seamless Gutters and Downspouts
Gutters that hang straight, drain to the right corner and stay on the house through a Minnesota winter, hung on fascia that has been checked first.
Read moreVinyl Siding Installation and Replacement
New vinyl siding that stays flat and stays on: the wrap and flashing underneath done properly, the panels hung with room to move, and the windows and doors trimmed so they do not look like an afterthought.
Read moreAttic Insulation Blown In — Air Sealed First, Then Filled
Ice dams, a furnace that never shuts off, a bedroom that is cold at the ceiling: the attic is the first place to look and the best payback in the house when the air sealing is done before the fluff.
Read moreAluminum Siding Replacement — Dented, Chalking Panels Off, New Siding
The aluminum siding has been on since the sixties, the paint rubs off white on your hand, and every panel below shoulder height has a dent in it.
Read moreBoard and Batten Siding Installation — Gable Accents and Whole Walls
The gables in board and batten and the rest in lap, or the whole house vertical: we lay out the battens so they land square at the corners and flash the panel joints so the look holds up to Minnesota weather.
Read morePage reviewed October 1, 2026 · JMB Builders LLC, MN license BC809005 · All siding pages
Where we work
Siding near you
Based in Zimmerman, scheduling across the Twin Cities metro. Closest first: